BLACK RESTORE INSTRUCTIONS

Download BLACK RESTORE INSTRUCTIONS.doc

PROPER PREPARATION IS THE KEY TO A LASTING FINISH!
DO NOT CLEAN SURFACES IN DIRECT SUNLIGHT OR WHEN HOT.

Caution, tire cleaner may stain bare aluminum, test small area first.

1. It is important to follow the cleaning instructions carefully to yield the best results.

1. CAUTION:  Liquid consistency is very thin, and could easily spill and stain surfaces.  Set opened bottle on waterproof pad to protect floors and driveways.  Keep a wet rag handy as spills dry very quickly

3. SprayTUF SHINE Tire Cleaner on tire/trim and allow it to set for 60 seconds.  Wet tire brush only with hose and scrub thoroughly around raised letters and grooves. Scrub in the direction of grooves, then 90 degrees to them. Rinse brush thoroughly after each scrubbing with direct stream of water from hose.  Do one tire/trim section at a time.
4. REPEATthis process a second time, or as needed, UNTIL SUDS APPEAR WHITE.  The white suds indicate the tire is clean.  This ensures that the tire/trim is properly prepared for the TUF SHINE Black Restore finish.  Black Restore will stick to rubber, but it will not stick to silicone.  That’s why this initial cleaning process is so important. Investing the extra time to properly clean the tires/trim will yield excellent results.
5. The tire/trim should have adull black lookwhen properly cleaned.
6. Use the Tire Cleaner for initial cleaning only.  The Tire Cleaner will dull the Black Restore finish and may remove portions of it.Applying Black Restore
7. Wear gloves provided to protect skin against staining.Also protect the surface area under and around the tire/trim to avoid staining those areas.
8. Shake well.Apply to COOL, DRY surfaces only. DO NOT APPLY IN DIRECT SUNLIGHT, OR IN COLD TEMPERATURES BELOW 5O DEGREES F.
9. Open andpressdispenser nozzle into sponge and dispense a small amount into the applicator sponge to prime the sponge.
10. Apply a smooth even coat. For tires, follow the circular pattern of the tire.Smooth out any runs.  If any black residue is drawn onto wheels or paint, wipe off immediately with a damp towel.  Allow the product to dry between coats.  Liberal applications of 2^nd and 3^rd coats may be needed.  Draw out any runs.  Dried on product can be removed with rubbing alcohol on a soft slightly damp cloth.
11. When done applying Black Restore, rinse applicator sponge thoroughly with water for future use.
12. We recommend that you top coat over Black Restore with 1 or more coats ofTUF SHINE Tire Clearcoatfor additional shine and protection.
13. Care for the tires as you would the car’s paint.Use clear water and soft car wash brush or mild soap and water for heavier dirt and mud.  This will prolong the finish.  Re-apply TUF SHINE Black Restore and/or clearcoat as needed.

Bulk Purchases:  If purchasing in bulk, we recommend shaking contents well and pouring product into smaller bottles for dispensing, and use dispensing spout.

Once the surface is clean, BLACK RESTORE may be applied with a foam brush or the applicator sponge included.  WEAR RUBBER GLOVES to protect hands from staining.  Rinse sponge with mild soap and water for future use.

Once dry, apply a minimum of two coats of the TUF SHINE Tire Clearcoat for added shine and protection.  The finished surface will now withstand repeated pressure washings and retain a clean appearance for an extended period of time.

GOLF CARTS

BLACK RESTORE will revitalize faded and oxidized gray and black panels, cup holders, floor mats, tires, etc.  Additional coats may be necessary, depending on the condition of the surface. Two to three coats are usually sufficient.

 CAUTION:  Liquid consistency is very thin, and could easily spill.  Set opened bottle on waterproof pad to protect floors and driveways.  Keep a wet rag handy as spills dry very quickly.

TUF SHINE, Inc.  801-520-5570